Showing results: 361 - 375 of 549 items found.
-
ACUTRONIC Switzerland Ltd
Combining a 3-Axis Flight Motion Simulator (FMS) with a 2-Axis Target Motion Simulator (TMS) leads to a 5-Axis motion simulator design. This allows comprehensive HardWare-In-the-Loop tests (HWIL) for testing and development of guided missiles, munitions and other inertial systems. Almost 100% of all HWIL systems worldwide delivered over the last 50 years have been designed and built by ACUTRONIC and CARCO Electronics.
-
TX4000 -
BI Communications
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
Amprobe Test Tools
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
888 PMR -
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● Indicates motor rotation/wiring.● Indicates battery status.● Phase rotation and motor rotation indication works from as low as 1Vac.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 100 Vac. ● Very low consumption.● Fused. ● Lightweight, robust and compact.● Works from 2 Hz to 400 Hz Sine.
-
Extech PRC15 -
Extech Instruments Corporation
The PRC15 enables plant maintenance and electrical technicians to test and calibrate a wide variety of process control equipment, including transmitters, transducers, indicators, sensors, instrumentation, robotic systems, thermocouples, and other industrial system components. Includes test leads, alligator clips, 100V-240V AC universal adaptor with 4 plugs, six AA batteries, and hard carrying case.
-
MBT300 -
Matco Tools
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
1120 ER -
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
Triplett Test Equipment & Tools
compact digital multimeter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Voltage, DC Current, Resistance, Continuity, Diode Test, Transistor hFE, and Temperature. The rubberized boot provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. The Model 1101-B is well suited for a variety of commercial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads with alligator clips, Type K bead probe and battery (9V).
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
2713 PU -
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
Comtest Engineering bv
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
UTOR
Production teams often refer to automation testing like it’s the holy grail. But when it comes to user experience, there’s no replacement for the human eye. While automated tests focus on repetitive tasks, manual QA testers come up with creative use cases and provide a lot more value. Very often, our recommendations helped improve the products and even lead them in new, more successful directions.
-
ED-205 -
Standard Electric Works Co., Ltd
● Dimension：91(L) × 103(W) × 100(D)mm● Deflection Angle : 90°● Scale Length：Approx. 65mm ● Terminal： 4mm socket captive head, suitable for wire or pin-type test lead.● Material And Color： Acrylic resin meter cover, white scale plate, plastic stand in black.● Safety Standard： IEC/EN 61010-1 CAT Ⅱ 300V EN 61326-1 EN 61000-4-2 EN 61000-4-3
-
XD71 -
Hangzhou Xihu Electronic Institute
The device is used for power transformer power outage routine test items to do automated testing.Which is characterized by dielectric loss, insulation resistance, DC resistance, tap-changer switching characteristics, short circuit impedance and variable ratio of six test items are concentrated in an instrument,so that the instrument function, test power and test lead height fusion.Field test, just start wiring once, at the end of unplugging wiring once,the middle process by the test personnel in the computer terminal to send command control,the test system automatically completes all or part of the above test items.
-
GET-100 -
ShinewayTech
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
